1991 Mazda Miata

1991 Mazda Miata wheel fitment at a glance

This 1991 Mazda Miata is running Work Wheels CR01 in 15x10.5 -22 at all four corners, wrapped in 195/50R15 Dunlop DIREZZA DZ101 tires.

It sits on stock suspension with a flush stance, meaning the wheel face lines up with the fender.

If you are searching for Mazda Miata wheel fitment, Work Wheels CR01 on a Mazda Miata, 15x10.5 -22 wheels on a Miata, or what tire size goes with that setup, this build is a real-world answer, photographed and measured by the owner.

Work Wheels CR01 15x10.5 -22 specs

The wheels are 15-inch in diameter and 10.5 inches wide with a -22 offset, in the 4x100 bolt pattern the Mazda Miata uses.

A -22 offset on a 10.5-inch wide wheel puts the wheel face in a very aggressive position at or past the fender. Lower offset moves the wheel outward; higher offset tucks it in.

Work Wheels CR01 15x10.5 -22 on a Mazda Miata is a common Miata question, and this page shows exactly how it sits, how it clears, and what the owner changed to make it work.

195/50R15 tires on 15x10.5 wheels

The tire size is 195/50R15: a 195 mm section width with a 50 aspect ratio on the 15-inch wheel, which gives a stretched fit (the tire is narrower than the wheel, which pulls the sidewall in and helps clear the fender).

The owner chose Dunlop DIREZZA DZ101. We stock Arroyo Grand Sport AS 195/50R15 at $84 each in this size, and other 195/50R15 tires through the 195/50R15 tire search.

Searching for 195/50R15 tires on a Mazda Miata, or the right tire size for 15x10.5 -22 wheels? This is one owner's proven combination, and every wheel and tire package we sell ships mounted, balanced and ready to bolt on.

Suspension, stance and clearance

This Mazda Miata is on stock suspension, so the ride height is factory and the fitment you see here works without lowering the car.

No rubbing at all, front or rear, no spacers, rolled fenders. Rolling or pulling the fender is what most owners do once the wheel sits this close; it keeps the tire from catching the lip over bumps.

Stance: flush. The wheel face lines up with the fender. Flush fitment on a Mazda Miata comes down to the offset and width above; copy them and you get the same result.

Will 15x10.5 -22 fit a Mazda Miata?

Will Work Wheels CR01 15x10.5 -22 fit a 1991 Mazda Miata? This owner's answer is yes, with no rubbing.

6 other Mazda Miata builds in the gallery run sizes like 16x9.5, 15x8, 16x7, 16x8, so you can compare offsets, tire sizes and suspension before you order. See all Mazda builds.

Our fitment guarantee covers wheels bought through wheels that fit the 1991 Mazda Miata: pick the car, and every size shown is one we have checked for bolt pattern, hub bore and clearance.

Buy the same wheels and tires for your Mazda Miata

We sell this wheel in the closest size we carry: Work Meister Cr01 4x100 15x10.5+-9 A Disk Bright Buff Finish is $820 each, about $3,280 for the set of four, made to order. Add tires on the product page and it ships as a mounted and balanced Mazda Miata wheel and tire package with free shipping.

Financing is available on every set, and 1991 Mazda Miata wheels ship free when bought as a wheel and tire package.

About this build

Every car in the Threepieceus gallery was submitted by its owner or collected from real builds, with the wheel size, offset, tire size, suspension and clearance recorded as fitted. Check two or three builds with the same Mazda Miata and size before you order, and add your own ride once it is done so the next owner can see what fits.