1999 Mazda Miata

1999 Mazda Miata wheel fitment at a glance

This 1999 Mazda Miata is running JR-Wheels Japan-Racing Jr19 in Gunmetal in 16x8 +0 at all four corners, wrapped in 205/40R16 Federal SS 595 tires.

It sits on VMaxx coilovers with a flush stance, meaning the wheel face lines up with the fender.

If you are searching for Mazda Miata wheel fitment, JR-Wheels Japan-Racing Jr19 on a Mazda Miata, 16x8 +0 wheels on a Miata, or what tire size goes with that setup, this build is a real-world answer, photographed and measured by the owner.

JR-Wheels Japan-Racing Jr19 16x8 +0 specs

The wheels are 16-inch in diameter and 8 inches wide with a +0 offset.

A +0 offset on a 8-inch wide wheel puts the wheel face in a very aggressive position at or past the fender. Lower offset moves the wheel outward; higher offset tucks it in.

JR-Wheels Japan-Racing Jr19 16x8 +0 on a Mazda Miata is a common Miata question, and this page shows exactly how it sits, how it clears, and what the owner changed to make it work.

205/40R16 tires on 16x8 wheels

The tire size is 205/40R16: a 205 mm section width with a 40 aspect ratio on the 16-inch wheel, which gives a square fit (tire and wheel are about the same width, the clean look most people go for).

The owner chose Federal SS 595. We stock Accelera PHI R 205/40R16 at $102 each in this size, and other 205/40R16 tires through the 205/40R16 tire search.

Searching for 205/40R16 tires on a Mazda Miata, or the right tire size for 16x8 +0 wheels? This is one owner's proven combination, and every wheel and tire package we sell ships mounted, balanced and ready to bolt on.

Suspension, stance and clearance

The car is lowered on VMaxx coilovers, which lets the owner dial in ride height and camber to clear 16x8 +0 and get the flush look.

No rubbing at all, front or rear, no spacers, rolled fenders. Rolling or pulling the fender is what most owners do once the wheel sits this close; it keeps the tire from catching the lip over bumps.

Stance: flush. The wheel face lines up with the fender. Flush fitment on a Mazda Miata comes down to the offset and width above; copy them and you get the same result.

Will 16x8 +0 fit a Mazda Miata?

Will JR-Wheels Japan-Racing Jr19 16x8 +0 fit a 1999 Mazda Miata? This owner's answer is yes, on VMaxx coilovers, with no rubbing.

6 other Mazda Miata builds in the gallery run sizes like 16x9.5, 15x8, 16x7, 16x9, so you can compare offsets, tire sizes and suspension before you order. See all Mazda builds.

Our fitment guarantee covers wheels bought through wheels that fit the 1999 Mazda Miata: pick the car, and every size shown is one we have checked for bolt pattern, hub bore and clearance.

Buy the same wheels and tires for your Mazda Miata

JR-Wheels Japan-Racing Jr19 is not something we carry today. For the same look on your Miata, browse wheels that fit the 1999 Mazda Miata in 16-inch sizes near +0 offset; the Mazda Miata wheel and tire packages there ship mounted and balanced.

Financing is available on every set, and 1999 Mazda Miata wheels ship free when bought as a wheel and tire package.

About this build

Every car in the Threepieceus gallery was submitted by its owner or collected from real builds, with the wheel size, offset, tire size, suspension and clearance recorded as fitted. Check two or three builds with the same Mazda Miata and size before you order, and add your own ride once it is done so the next owner can see what fits.