1993 Mazda RX-7

1993 Mazda RX-7 wheel fitment at a glance

This 1993 Mazda RX-7 is running Work Wheels VS-XX, staggered: 18x10 +0 up front and 18x13 +20 in the rear, wrapped in 225/40R18 front and 295/30R18 rear Falken FK452 tires.

It sits on lowering springs with a flush stance, meaning the wheel face lines up with the fender.

If you are searching for Mazda RX-7 wheel fitment, Work Wheels VS-XX on a Mazda RX-7, 18x10 +0 wheels on a RX-7, or what tire size goes with that setup, this build is a real-world answer, photographed and measured by the owner.

Work Wheels VS-XX 18x10 +0 specs (staggered)

The wheels are 18-inch in diameter and 10 inches wide with a +0 offset up front, and 18-inch by 13 inches at +20 in the rear.

A +0 offset on a 10-inch wide wheel puts the wheel face in a very aggressive position at or past the fender. Lower offset moves the wheel outward; higher offset tucks it in. The rear +20 offset on the 13-inch wheel keeps the rear in line with the front.

Work Wheels VS-XX 18x10 +0 on a Mazda RX-7 is a common RX-7 question, and this page shows exactly how it sits, how it clears, and what the owner changed to make it work.

225/40R18 / 295/30R18 tires on 18x10 wheels

The tire size is 225/40R18 front and 295/30R18 rear: a 225 mm section width with a 40 aspect ratio on the 18-inch wheel, which gives a stretched fit (the tire is narrower than the wheel, which pulls the sidewall in and helps clear the fender).

The owner chose Falken FK452. We stock Ironman IRON iMOVE Gen 3 AS 225/40ZR18XL at $89 each in this size, and other 225/40R18 tires through the 225/40R18 tire search.

Searching for 225/40R18 tires on a Mazda RX-7, or the right tire size for 18x10 +0 wheels? This is one owner's proven combination, and every wheel and tire package we sell ships mounted, balanced and ready to bolt on.

Suspension, stance and clearance

The drop comes from lowering springs, the simplest way to close the fender gap on a Mazda RX-7 while keeping the factory shocks.

No rubbing at all, front or rear, no spacers, rolled fenders front and pulled fenders rear. Rolling or pulling the fender is what most owners do once the wheel sits this close; it keeps the tire from catching the lip over bumps.

Stance: flush. The wheel face lines up with the fender. Flush fitment on a Mazda RX-7 comes down to the offset and width above; copy them and you get the same result.

Will 18x10 +0 fit a Mazda RX-7?

Will Work Wheels VS-XX 18x10 +0 fit a 1993 Mazda RX-7? This owner's answer is yes, on lowering springs, with no rubbing.

6 other Mazda RX-7 builds in the gallery run sizes like 18x10 / 18x11, 18x9.5, 17x9 / 17x10, 17x7.5, 18x11, so you can compare offsets, tire sizes and suspension before you order. See all Mazda builds.

Our fitment guarantee covers wheels bought through wheels that fit the 1993 Mazda RX-7: pick the car, and every size shown is one we have checked for bolt pattern, hub bore and clearance.

Buy the same wheels and tires for your Mazda RX-7

Work Wheels VS-XX is not something we carry today. For the same look on your RX-7, browse wheels that fit the 1993 Mazda RX-7 in 18-inch sizes near +0 offset; the Mazda RX-7 wheel and tire packages there ship mounted and balanced.

Financing is available on every set, and 1993 Mazda RX-7 wheels ship free when bought as a wheel and tire package.

About this build

Every car in the Threepieceus gallery was submitted by its owner or collected from real builds, with the wheel size, offset, tire size, suspension and clearance recorded as fitted. Check two or three builds with the same Mazda RX-7 and size before you order, and add your own ride once it is done so the next owner can see what fits.