1993 Mazda RX-7

1993 Mazda RX-7 wheel fitment at a glance

This 1993 Mazda RX-7 is running CCW Wheels Classic Drag Version, staggered: 16x5.5 +0 up front and 16x10.5 +0 in the rear, wrapped in 235/45R16 front and 315/40R16 rear Mickey Thompson Baja MTZP3 tires.

It sits on coilovers with a flush stance, meaning the wheel face lines up with the fender.

If you are searching for Mazda RX-7 wheel fitment, CCW Wheels Classic Drag Version on a Mazda RX-7, 16x5.5 +0 wheels on a RX-7, or what tire size goes with that setup, this build is a real-world answer, photographed and measured by the owner.

CCW Wheels Classic Drag Version 16x5.5 +0 specs (staggered)

The wheels are 16-inch in diameter and 5.5 inches wide with a +0 offset up front, and 16-inch by 10.5 inches at +0 in the rear.

A +0 offset on a 5.5-inch wide wheel puts the wheel face in a very aggressive position at or past the fender. Lower offset moves the wheel outward; higher offset tucks it in. The rear +0 offset on the 10.5-inch wheel keeps the rear in line with the front.

CCW Wheels Classic Drag Version 16x5.5 +0 on a Mazda RX-7 is a common RX-7 question, and this page shows exactly how it sits, how it clears, and what the owner changed to make it work.

235/45R16 / 315/40R16 tires on 16x5.5 wheels

The tire size is 235/45R16 front and 315/40R16 rear: a 235 mm section width with a 45 aspect ratio on the 16-inch wheel, which gives a meaty fit (the tire is wider than the wheel, so the sidewall bulges a little and gives more cushion).

The owner chose Mickey Thompson Baja MTZP3. See every 235/45R16 tire we carry for this size.

Searching for 235/45R16 tires on a Mazda RX-7, or the right tire size for 16x5.5 +0 wheels? This is one owner's proven combination, and every wheel and tire package we sell ships mounted, balanced and ready to bolt on.

Suspension, stance and clearance

The car is lowered on coilovers, which lets the owner dial in ride height and camber to clear 16x5.5 +0 and get the flush look.

No rubbing at all, front or rear, no spacers, pulled and rolled fenders. Rolling or pulling the fender is what most owners do once the wheel sits this close; it keeps the tire from catching the lip over bumps.

Stance: flush. The wheel face lines up with the fender. Flush fitment on a Mazda RX-7 comes down to the offset and width above; copy them and you get the same result.

Will 16x5.5 +0 fit a Mazda RX-7?

Will CCW Wheels Classic Drag Version 16x5.5 +0 fit a 1993 Mazda RX-7? This owner's answer is yes, on coilovers, with no rubbing.

6 other Mazda RX-7 builds in the gallery run sizes like 18x10 / 18x11, 18x9.5, 17x9 / 17x10, 17x7.5, 18x11, so you can compare offsets, tire sizes and suspension before you order. See all Mazda builds.

Our fitment guarantee covers wheels bought through wheels that fit the 1993 Mazda RX-7: pick the car, and every size shown is one we have checked for bolt pattern, hub bore and clearance.

Buy the same wheels and tires for your Mazda RX-7

CCW Wheels Classic Drag Version is not something we carry today. For the same look on your RX-7, browse wheels that fit the 1993 Mazda RX-7 in 16-inch sizes near +0 offset; the Mazda RX-7 wheel and tire packages there ship mounted and balanced.

Financing is available on every set, and 1993 Mazda RX-7 wheels ship free when bought as a wheel and tire package.

About this build

Every car in the Threepieceus gallery was submitted by its owner or collected from real builds, with the wheel size, offset, tire size, suspension and clearance recorded as fitted. Check two or three builds with the same Mazda RX-7 and size before you order, and add your own ride once it is done so the next owner can see what fits.