2005 Honda S2000

2005 Honda S2000 wheel fitment at a glance

This 2005 Honda S2000 is running Work Wheels Meister S1 3P in 18x11.5 -35 at all four corners, wrapped in 265/40R18 Nitto Invo tires.

It sits on Air Lift Performance air suspension with a flush stance, meaning the wheel face lines up with the fender.

If you are searching for Honda S2000 wheel fitment, Work Wheels Meister S1 3P on a Honda S2000, 18x11.5 -35 wheels on a S2000, or what tire size goes with that setup, this build is a real-world answer, photographed and measured by the owner.

Work Wheels Meister S1 3P 18x11.5 -35 specs

The wheels are 18-inch in diameter and 11.5 inches wide with a -35 offset, in the 5x100 bolt pattern the Honda S2000 uses.

A -35 offset on a 11.5-inch wide wheel puts the wheel face in a very aggressive position at or past the fender. Lower offset moves the wheel outward; higher offset tucks it in.

Work Wheels Meister S1 3P 18x11.5 -35 on a Honda S2000 is a common S2000 question, and this page shows exactly how it sits, how it clears, and what the owner changed to make it work.

265/40R18 tires on 18x11.5 wheels

The tire size is 265/40R18: a 265 mm section width with a 40 aspect ratio on the 18-inch wheel, which gives a stretched fit (the tire is narrower than the wheel, which pulls the sidewall in and helps clear the fender).

The owner chose Nitto Invo. We stock Continental CON ExtremeContact DWS06 Plus 265/40ZR18XL at $251 each in this size, and other 265/40R18 tires through the 265/40R18 tire search.

Searching for 265/40R18 tires on a Honda S2000, or the right tire size for 18x11.5 -35 wheels? This is one owner's proven combination, and every wheel and tire package we sell ships mounted, balanced and ready to bolt on.

Suspension, stance and clearance

It rides on Air Lift Performance air suspension, so it can lay low parked and raise up to drive.

No rubbing at all, front or rear, no spacers, pulled and rolled fenders. Rolling or pulling the fender is what most owners do once the wheel sits this close; it keeps the tire from catching the lip over bumps.

Stance: flush. The wheel face lines up with the fender. Flush fitment on a Honda S2000 comes down to the offset and width above; copy them and you get the same result.

Will 18x11.5 -35 fit a Honda S2000?

Will Work Wheels Meister S1 3P 18x11.5 -35 fit a 2005 Honda S2000? This owner's answer is yes, on Air Lift Performance air suspension, with no rubbing.

6 related builds run sizes like 18x9.5, 18x10.5, 18x9.5 / 19x11.5, 19x9.5 / 19x10, 19x10.5, so you can compare offsets, tire sizes and suspension before you order. See all Honda builds.

Our fitment guarantee covers wheels bought through wheels that fit the 2005 Honda S2000: pick the car, and every size shown is one we have checked for bolt pattern, hub bore and clearance.

Buy the same wheels and tires for your Honda S2000

We sell this exact wheel: Work Meister S1 3P 5x100 18x11.5-35 A Disk Black is $1,040 each, about $4,160 for the set of four, made to order. Add tires on the product page and it ships as a mounted and balanced Honda S2000 wheel and tire package with free shipping.

Financing is available on every set, and 2005 Honda S2000 wheels ship free when bought as a wheel and tire package.

About this build

Build and photos by @Sensualwhitechocolate_. Every car in the Threepieceus gallery was submitted by its owner or collected from real builds, with the wheel size, offset, tire size, suspension and clearance recorded as fitted. Check two or three builds with the same Honda S2000 and size before you order, and add your own ride once it is done so the next owner can see what fits.