How Much Torque Do Lug Nuts Need?

By THREEPIECE.US Published Nov 15th 2026
Editorial note: ThreePiece.us fitment guides are maintained by our wheel and tire fitment team.

Lug nuts should be tightened to the torque figure in your owner's manual, which for the popular cars and trucks listed below runs from 76 to 150 ft-lbs. Do the final pass with a torque wrench, and check them once more after the first short drive.

What the manual says for some popular vehicles

These are the factory figures listed in our fitment data. Use them to get a feel for the range, and confirm your own in the owner's manual, because the figure can change between model years.

Lug torque by vehicle
VehicleThreadTorque
2021 Toyota CamryM12x1.576 ft-lbs
2022 Toyota CorollaM12x1.576 ft-lbs
2022 BMW 330iM14x1.25 lug bolts103 ft-lbs
2022 Tesla Model 3M14x1.5129 ft-lbs
2022 Jeep WranglerM14x1.5130 ft-lbs
2022 Ram 1500M14x1.5130 ft-lbs
2021 Chevrolet Silverado 1500M14x1.5140 ft-lbs
2022 Ford F-150M14x1.5150 ft-lbs

If you can't find a figure

Wheel makers publish a fallback chart by stud size for when there's no factory figure to go by. This one is Konig's, and Konig is clear that the owner's manual takes precedence over it. You can see why in the table above, where the trucks with 14 mm studs are specified well above the chart.

Konig's recommended torque by stud size
Stud sizeTorque
7/16 inch55 to 65 ft-lbs
12 mm70 to 80 ft-lbs
1/2 inch75 to 85 ft-lbs
14 mm85 to 95 ft-lbs
9/16 inch95 to 115 ft-lbs
5/8 inch135 to 145 ft-lbs

How to tighten them

  1. Start every nut by hand so you know the threads are engaged, then snug them with a wrench.
  2. Tighten in a crisscross pattern, going across the wheel from one nut to the one opposite, and bring them up in a couple of passes so the wheel pulls down evenly.
  3. Do the final pass with a torque wrench set to your figure.

Leave the impact gun out of the final tightening. McGard, which makes lug nuts and wheel locks, warns that an impact can't hold a set torque and that uneven or over tightening can damage the studs and the wheel and distort the brake rotors. McGard also says not to put oil, grease or anti-seize on the threads.

Check them again after a short drive

After you've fitted wheels, the nuts need one more check with the torque wrench once the car has been driven. McGard says to do it after 25 miles and Konig says after 60 to 90, and what we tell customers is to check them again somewhere in the first 50 to 100 miles. Any of those is fine as long as you do it.

Related

If you're fitting new wheels, make sure the nuts match them first: what size lug nuts do I need covers thread and seat. We carry lug nuts and lug bolts, and if a wheel still shakes after it's torqued, check whether you need hub centric rings.

Do you need to re-torque lug nuts?

Yes, once, after the first short drive on newly fitted wheels. McGard says after 25 miles and Konig says after 60 to 90 miles, so checking them somewhere in the first 100 miles covers it.

Can you use an impact wrench on lug nuts?

Not for the final tightening. McGard warns that an impact can't hold a set torque and can over tighten or unevenly tighten the nuts, which can damage studs and wheels and distort brake rotors. Finish with a torque wrench.

What pattern do you tighten lug nuts in?

Tighten them in a crisscross pattern, moving across the wheel to the opposite nut each time, which on a five lug wheel traces a star. Bring them up to full torque over a couple of passes.

Free shipping on all wheel & tire packages

Shop wheels for your car

Pick your year, make and model and see the wheels that fit.