The lug nuts you need have to match two things: the thread on your car's wheel studs and the seat in the wheel's lug holes. On late-model cars and trucks the thread is usually M12x1.5, M12x1.25 or M14x1.5, and most aftermarket wheels take a conical seat with a 60 degree taper.
The thread comes from the car and the seat comes from the wheel, so when you change wheels the thread stays the same and the seat is the part that can change.
Thread size
A size like M12x1.5 reads as a 12 mm stud with 1.5 mm from one thread to the next. Always start a new nut by hand, and if it gets tight after a turn or two, stop and check the size before you put a wrench on it. Here's what our fitment data lists for some popular vehicles.
| Thread | Vehicles | Nut or bolt |
|---|---|---|
| M12x1.5 | 2022 Honda Civic, 2021 Toyota Camry, 2022 Mazda 3, 2022 Mazda MX-5 Miata, 2022 Kia K5, 2022 Ford Bronco | Lug nuts |
| M12x1.25 | 2019 Subaru BRZ, 2020 Toyota 86, 2022 Infiniti Q50 | Lug nuts |
| M14x1.5 | 2022 Ford Mustang, 2022 Ford F-150, 2021 Chevrolet Silverado 1500, 2022 Chevrolet Camaro, 2022 Dodge Challenger, 2022 Jeep Wrangler, 2022 Ram 1500, 2022 Tesla Model 3 | Lug nuts |
| M14x1.5 | 2019 Volkswagen GTI | Lug bolts |
| M14x1.25 | 2022 BMW 330i | Lug bolts |
Those are the three we see most, and they aren't the only ones. McGard's cone seat catalog also lists 7/16-20, 1/2-20, 9/16-18, M12x1.75 and M14x2.0, so check your own year and model before you order.
Seat type
The seat is the surface where the nut presses against the wheel, and there are three you'll run into.
| Seat | What it looks like | Where you find it |
|---|---|---|
| Conical (also called cone, tapered or acorn) | The bottom of the nut is a 60 degree cone. | Most aftermarket wheels. |
| Ball (also called radius) | The bottom of the nut is rounded like part of a ball. | Some factory wheels. |
| Shank with a flat washer (also called mag) | A straight shank drops into the hole and a flat washer sits on the wheel. | Some factory wheels. |
The seat on the nut has to match the seat in the wheel. Konig says it directly about its own wheels, which take a conical seat like most aftermarket wheels, and ball seat or flat washer hardware from the factory isn't compatible with them. So if your factory nuts are ball seat or washer style, you need new conical ones for the new wheels, even though the thread hasn't changed.
Small lug holes
Some wheels have lug holes too narrow for a regular socket to fit around the nut. Those take a smaller diameter nut, sold as tuner or spline drive, that you tighten with a matching key. Konig recommends that style for dual-drilled wheels, where two bolt patterns share one wheel and the holes sit close together.
How much thread has to catch
McGard's rule is that the nut has to thread on by at least the diameter of the stud. On an M12x1.5 stud that's 12 mm of thread, which is 8 full turns, and on M12x1.25 or M14x1.5 it's 9 to 10 turns. Count the turns on one nut by hand the first time you fit a new set, and if you come up short, don't drive on it.
Where to find them
We carry lug nuts and lug bolts by thread size, and locks are covered in our wheel locks guide. Once they're on, torque them properly. If you'd like us to confirm the thread and seat for your car and wheels, call or text 813-535-5801.
Can I use my stock lug nuts on aftermarket wheels?
Only if they have the same seat as the new wheels. Most aftermarket wheels take a conical seat, so factory ball seat or flat washer nuts won't work on them and you'll need conical nuts in your car's thread size.
Are all lug nuts the same size?
No. Thread size depends on the vehicle, and M12x1.5, M12x1.25 and M14x1.5 are the ones we see most. The seat type depends on the wheel.
What's the difference between lug nuts and lug bolts?
A lug nut threads onto a stud that's fixed in the hub, and a lug bolt threads into the hub itself. In our fitment data the BMW 330i and Volkswagen GTI use lug bolts, and the thread and seat have to match the same way they do with nuts.